The EAGLE’s ergonomic design offers easy access to controls such as autocalibration, alarm silence, demand zero, peak hold and a wide variety of other features. Each channel has 2 alarm levels plus TWA and STEL alarms for toxic channels. Alarm levels are adjustable and can be latching or self resetting.
Standard features on the EAGLE are not available on most other competitive units such as PPM/LEL hydrocarbon detection (5 ppm resolution) and a methane elimination switch for environmental applications. For quick response and recovery, the EAGLE has a strong internal pump which can draw samples from over 125 feet.

The EAGLE will con-tinuously operate for over 30 hours on alkaline batteries or 18 hours on Ni-Cads. Many accessories such as long hoses, special probes, datalogging, continuous operation adapters, remote alarms and strobes, dilution fittings, inter-nal hydrophobic filter, etc, are available to help satisfy almost any application. Rugged, weatherproof, easy to operate and maintain, the EAGLE is the industry’s answer to portable gas detection.

Built around our high-quality micro-sensor technology, the GX-2003 is RKI’s smallest personal 5-in-1 gas monitor with a built in sample pump. Weighing only 11 ounces, it has many features which set the GX-2003 apart from the competition. For example, it can monitor the standard confined space gases (LEL combustibles, Oxygen deficiency, Carbon Monoxide, and Hydrogen Sulfide), however it can also measure 100% volume combustibles and dynamically display either % LEL, or % volume with its auto-ranging ability.
The GX-2003 is equipped with datalogging and a sizable memory capacity of up to 600 hours of log time. With this much capacity, the GX-2003 can store 100 alarm events, 100 trouble events, the last 20 calibrations, and up to 8 alarm trends where data is collected automatically every 5 seconds for 30 minutes before and after an alarm occurs. Calibration intervals and reminders are user adjustable and can be set to either go into alarm or to lock the user out of normal measurement mode once a calibration period has expired. Calibrations can be performed on all channels automatically or individually in single calibration mode. The GX-2003 is also compatible with the Data Cal 2000 calibration station for simultaneous, hands-free service of up to 10 instruments.

1st alarm 10% LEL

2nd alarm 50% LEL

Over alarm 100% LEL

Low alarm 19.5%

High alarm 23.5%

Over alarm 40.0%

1st alarm 10 ppm

2nd alarm 30 ppm

TWA alarm 10 ppm
STEL alarm 15 ppm

Over alarm 100 ppm

RKI is proud to introduce the smallest and most affordable 4-gas monitor in the world, the GX-2001. Weighing only 6 ounces and about the size of a pager (2.8" H x 2.2" W x 1.1" D), the GX-2001 simultaneously monitors combustibles, oxygen, carbon monoxide, and hydrogen sulfide. The GX-2001 is armed with standard features like autocalibration, datalogging, rechargeable Ni-Cad batteries, a unique vibration alarm, STEL / TWA readings, peak hold and auto backlighting at alarm on a large LCD display, and it even tells the time. All of these controls and features are operated through 3 simple glow in the dark buttons. Utilizing either of the GX-2001's chargers, the standard charger or datalogging / charger station, it's Ni-Cad batteries will fully recharge in 90 minutes. Also available is the datalogging software program which is Windows 95, 98, ME compatible.
The GX-2001 is also designed around the world’s smallest gas sensors. Utilizing catalytic combustion, electrochemical and galvanic sensor technologies, each miniaturized sensor is manufactured with the same high quality control that has made Riken sensors and instruments the most reliable and long lasting monitoring devices in the industry

1st alarm 10% LEL

2nd alarm 50% LEL

Over alarm 100% LEL

Low alarm 19.5%

High alarm 23.5%

Over alarm 40.0%

1st alarm 10 ppm

2nd alarm 30 ppm

TWA alarm 10 ppm

STEL alarm 100 ppm

Over alarm

Individuals need personal protection in hazardous areas at all times without adding extra bulky equipment, and the 01 Series can provide that kind of protection at an affordable price. The GP-01, OX-01, CO-01, HS-01 and HS-01S models are personal single gas monitors designed for personal protection from combustible hydrocarbons, oxygen deficiency, hydrogen sulfide, or carbon monoxide. Each model is controlled by a microprocessor for reliability and advanced capabilities. Each model can be operated continuously for at least 3,000 hours on (2) AAA size alkaline batteries except the GP-01, which operates for 16 hours. The 01 models have 2 preset alarms that are user adjustable and each version is also equipped with visual, audible, and vibration alarms as standard. The replacement sensors are inexpensive, easily field replaceable, have a life expectancy of 2 years, and are interchangeable with other RKI monitors such as the GX-2001, GX-2003, and GasWatch 2 models. The entire 01 Series monitors are safe for use in hazardous locations, classified as intrinsically safe by CSA to U.S. and Canadian standards for Class I, Division 1, Groups A, B, C, and D atmospheres. For additional information please contact one of our reps.

The Beacon™ 800 is a simplified, versatile, low cost fixed system controller for one to eight points of gas detection. It is microprocessor controlled and is capable of accepting up to 8 separate 4-20 mAsensor transmitters which can be either 2 or 3 wire. The Beacon™ 800 can be powered by either 24 VDC or 115 VAC. It is simple to operate and comes complete with a wall mount installation kit.

2 relays per channel 10 amp rating, SPDT isolated contacts.
1 set of common relays:
2 for gas alarm levels
1 for malfunction
Relays fully programmable for:
Increasing or decreasing alarms
Latching or self reset
Normally energized or normally de-energized
Time delay for alarm on and alarm off

Built-in audible alarm, 94 dB, mounted on enclosure.
Coded Output:
pulsing = gas alarm
steady = Fail

Gas detection should not be complicated. The Beacon 110 is gas detection simplified.

The Beacon 110 is a powerful, low cost fixed system controller for one point of gas detection. It is microprocessor controlled, versatile, simple to install and operate, and priced to be the industry’s best value single gas detection controller. It is capable of accepting RKI sensors directly for LEL level combustibles, Oxygen, Hydrogen Sulfide, or Carbon Monoxide. The Beacon 110 can also accept any 4-20 mA transmitter (2 or 3 wire, 24 VDC). Sensors can be mounted directly at the Beacon 110 housing, or can be wired remote from the controller.

3 relays - 10 amp rating (at 115 VAC), SPDT isolated contacts.
2 relays for gas alarms and 1 trouble relay.
Relays fully programmable for: increasing or decreasing alarm, latching or self reset, normally energized or normally de-energized, time delay for alarm on and alarm off

Built-in audible alarm, 94 dB, mounted on enclosure Coded output: pulsing = gas alarm, steady = fail

The Beacon 410 is a highly configurable, microprocessor-based, flexible and easy to use 4 channel gas monitor. It simultaneously displays the gas type, readings, and status for 4 channels of gas detection. It can monitor any combination of direct connect sensors (LEL combustibles, Oxygen, Hydrogen Sulfide, Carbon Monoxide, and Carbon Dioxide) as well as any 4-20mA transmitters.

Each channel has 3 fully configurable alarm points. A built-in silenceable audible alarm alerts you to alarm conditions. Each channel also has 2 dedicated fully configurable relays and there is a bank of common relays as well. The common relays can optionally be configured as additional channel relays allowing up to 3 alarm relays per channel.

Two flexible, programmable Form-C (C, NO, NC) relays per channel, plus five common relays (Fail, Alarm-1, Alarm-2, Alarm-3, Alarm-Any). Common relays may optionally be assigned to function as additional channel alarm relays, providing for up to three alarm relays per channel. 10A contact rating.

4 x 20 backlit LCD display

Sensors

65-2610RK
65-2610RK-05

65-2611RK (H2 Specific)

65-2611RK-05

65-2613RK
65-2613RK-05 *65-2614RK

65-2615RK-05

65-2616RK-05

65-2630RK-03

65-2619RK-CH4

65-2619RK-HC

0 - 100 % LEL

0 - 25.0 % Vol

0 - 100 ppm

0 - 300 ppm

0 - 5% Vol

0 - 100% LEL

Patented water repellent sensor coating (*Except for 65-2613RK and 65-2614RK)

Outputs

4-20 mA signal, into 500 ohms impedance max, corresponding to 0 - full scale

Modbus RTU output standard, fully configurable, 2-wire RS-485, 1200 to 19.2k baud

Alarms

Fully programmable alarm setpoints, increasing / decreasing, latching /
self-resetting, on delays, off delays, normally energized or de-energized,
programmable deadband, programmable smoothing filter

Visual LEDs. Alarm 1, Amber; Alarm 2, Red; Fail, Red

5 amp form C  contacts for alarm 1, alarm 2, and fail

Physical

Height: 8.5  (215 mm), Width: 5.2  (132 mm), Depth: 4.5  (114 mm)

Alphanumeric display with backlighting. 8 characters per line;
2 lines for gas concentration readout, plus user-friendly calibration and setup

Explosion proof for Class I, Div 1, Groups B, C, D.

NEMA 4, explosion proof, watertight, cast aluminum with o-ring seal and epoxy
powder coating

Magnet used for calibration functions. Calibrates without opening the housing.
Internal push-button controls also available for calibration and setup

Operating Environment

-4°F ~ 122°F (-20°C ~ 50°C)

5 - 95% RH non-condensing

Indoor or outdoor. Explosion proof for Class I, Div. 1, Groups B, C, and D. (Oxygen available in non XP version also)

Operating Voltage

19 VDC - 30 VDC

Approvals

65-2610RK-05
65-2611RK-05
C CSA US

65-2610RK-05

65-2611RK-05

C UL US

65-2613RK-05
C CSA US

C CSA US

C UL US

Warranty

One year material and workmanship

The RKI "S" series gas sensor/transmitters are highly reliable and very cost effective basic 4-20 mA transmitters for detection of common gas hazards. The "S" series transmitters are available for LEL, Oxygen, H2S, CO, or for 0 - 500 ppm Hydrocarbon detection (for various fuels or solvents). The electronics are encased inside a potted package to avoid damage from mechanical abuse or corrosion, and the amplifier is installed inside an explosion-proof enclosure. Sensors for LEL, H2S, CO, and ppm HC are explosion-proof with flame arrestors. The Oxygen sensor utilizes an internal I.S. barrier, so all 5 versions are designed for use in hazardous atmospheres.
The only tools required to calibrate the "S" series are a voltmeter, screwdriver, and cal gas. The zero and calibration functions are performed by adjusting potentiometers on the amplifiers. The amplifier has test jacks for connection of a voltmeter for calibration purposes, and the sensor response is viewed on the voltmeter as a 100mV to 500mV signal. Field calibration can be performed easily and quickly by one person.
The "S" series transmitters can be used either indoors or outdoors. The flame arrestors utilize a patented coating which makes them water repellent, and splash guards are also available for use in very wet environments.
The transmitter operates from 24 VDC (10.5VDC to 30 VDC), and provides a 4-20mAsignal which can be connected to a wide variety of controllers.